[1]Fei Feng, Shangyu Huang*, Zhenghua Meng, Jianhua Hu. Experimental study on tensile property of AZ31B magnesium alloy at different high strain rates and temperatures. Materials and Design, 57:10-20, 2014
[2]Fei Feng, Shangyu Huang*, Zhenghua Meng, JianhuaHu. A constitutive and fracture model for AZ31B magnesium alloy in the tensile state. Materials Science & Engineering A, 594: 334-343, 2014
[3]Fei Feng, Shangyu Huang*, Jianhua Hu, Zhenghua Meng, Yu Lei. Analysis of the bulging process of AZ31B magnesium alloy sheet with a uniform pressure coil. The International Journal of Advanced Manufacturing Technology, 69: 1537-1545, 2013.
[6]Zhenghua Meng, Shangyu Huang*, Jianhua Hu. Effects of process parameters on warm and electromagnetic hybrid forming of magnesium alloy sheets. Journal of Materials Processing Technology, 211(5): 863-867, 2011.
2005/08-2006/09, The Ohio State University, Material Processing Engineering, Visiting Professor
1996/02-1996/07, Harbin Institute of Technology, Plastic Working, In-service Education
1984/09-1987/03, Nanjing Aeronautical Institute, Aeronautics and Astronautics Manufacture Engineering, Master
1980/09-1984/07, Nanjing Aeronautical Institute, Aeronautics and Astronautics Manufacture Engineering,Bachelor
4.Working experience:
2010/03-Present, Wuhan University of Technology, Department of Material Processing, Professor/Director
2002/06-2010/03, Wuhan University of Technology, Department of Material Molding and Control Engineering,Professor/Director
2001/03-2002/06, Wuhan University of Technology, Institute of Plastic Forming and Computer Application,Professor /Director
2000/11-2001/03, Wuhan University of Technology, Division of Auto-body Design and Manufacture,Professor
5.Research field(no more than 3):
1)New processing technology for difficult-to-form or lightweight material
2)Simulation, optimization and precise control of material forming process
3)New fabrication and processing technology for microelectronic packaging materials
6.Research project(no more than 5):
1)The basic study on fabrication of environment friendly adhesion material in microelectronic packaging by electromagnetic compaction (Project of NSFC:51475345)
2)Research on the plastic deformation behaviors of high strength steel for auto-body in high strain rate and complex strain paths (Project of NSFC:51205298)
3)Basic research on eletromagnetic and warming hybrid forming of magnesium alloy sheet using uniform pressure coil (Project of NSFC:50875192)
7.Representative papers and works(no more than 10):
(1)Fei Feng, Shangyu Huang*, Zhenghua Meng, Jianhua Hu. Experimental study on tensile property of AZ31B magnesium alloy at different high strain rates and temperatures. Materials and Design, 57:10-20, 2014
(2)Fei Feng, Shangyu Huang*, Zhenghua Meng, JianhuaHu. A constitutive and fracture model for AZ31B magnesium alloy in the tensile state. Materials Science & Engineering A, 594: 334-343, 2014
(3)Fei Feng, Shangyu Huang*, Jianhua Hu, Zhenghua Meng, Yu Lei. Analysis of the bulging process of AZ31B magnesium alloy sheet with a uniform pressure coil. The International Journal of Advanced Manufacturing Technology, 69: 1537-1545, 2013.
(4)Feng Fei, Huang Shangyu*, Hu Jianhua, Lei Yu, Meng Zhenghua. Effects of temperature on electromagnetic forming of AZ31B magnesium alloy sheet. Journal of Plasticity Engineering,20(6):56-61, 2013.
(5)Lei Yu, Meng Zhenghua, Hu Jianhua, Feng Fei, Huang Shangyu. Experimental investigation on high rate forming of two kinds of typical High-strength steel in car manufacture. China Mechanical Engineering, 24(18):2529-2532, 2013.
(6)Zhenghua Meng, Shangyu Huang*, Jianhua Hu. Effects of process parameters on warm and electromagnetic hybrid forming of magnesium alloy sheets. Journal of Materials Processing Technology, 211(5): 863-867, 2011.
(7)Meng Zhenghua, Huang Shangyu*, Hu Jianhua. Experimental Research on Warm and Electromagnetic Hybrid Forming of Magnesium Alloy Sheet, Chinese Journal of Mechanical Engineering, 47(10):38-42, 2011.
(8)Yu Shihao, Huang Shangyu. Basic of Die&Mould CAD (“Eleventh Five-Year Plan” National Level Official Textbook), Wuhan: Wuhan University of Technology Press, 2009.
(9)Yu Shihao, Hua Lin, Huang Shangyu. Basic of CAD/CAM, Beijing:National Defence Industry Press, 2007.
(10)China Die&Mould Engineering Canon (Editor Article 3 in Volume 4 : Structure Design of Stamping Die & Mould), Beijing: Publishing House of Electronics Industry, 2007.
8.Contact information:
1) Tel: 18986281313
2) E-mail: huangshy@whut.edu.cn
3) Location of lab: Room 402 in The Material Building